Need Help? 83809862344 ( 9.00 )

Cheap, Reliable and Most Complete Geosystem Equipment

Shopping Cart: $0.00

You have no items in your shopping cart.

Leica Builder 400 9 Second Reflectorless Total Station 772733

Be the first to review this product

  • 50,000-point internal memory

  • 50 foot range

  • Laser plummet

  • On-board field software

  • USB stick and RS232 serial port

  • Theft protection

  • 20-hour battery life

  • Water resistant and dustproof to IP-55

  • Single graphic LCD display

  • Alphanumeric keyboard

Availability: In stock


Overview for the Leica Builder 400 9 Second Reflectorless Total Station

The Leica Builder 400 (9-Second) Reflectorless Total Station is a powerful tool that allows you to save time and money by precisely and accurately measuring even the most difficult locations - even if you've never used a total station before. Layout a construction site, collect height and angle data, perform control measurements, complete site preparation and earthworks, or even align concrete forms: the intuitive interface and pre-loaded application functions make it easy to get the job done in record time.

One-Person Operation

The Leica Builder Reflectorless Total Station allows you to take measurements up to 50 feet away without placing a prism pole at the end point of the location you need to measure. Not only do you save time and money, since only one person is needed to take measurements, but you'll be able to access locations that were previously too dangerous or inaccessible to reach, such as overhead power lines, bridges, scaffolding, past hostile pets, or across large bodies of water.

Easy Setup Wizard

Even novices can get started using the Leica Geosystems Total Station right from the beginning, by following the display of the computerized setup wizard. Graphic icons on the control panel's 6-line LCD display, as well as a 20-key alphanumeric keyboard similar to a cellphone, lead you through every step of the setup process. Follow the wizard to level the builder, define your control line, enter offset values from a plan, and set out or record the points; in just a few minutes your Leica Builder 400 will be set and ready to go.

Pinpoint Laser Technology for Precise Measurements

Get measurements with bulls-eye precision using the patented pinpoint laser technology of the Leica Builder. Other total stations use a wide laser beam, which can lead to inaccurate measurements by measuring not only the target point, but also the area surrounding the point you'd like to measure. The Leica optical device's laser, however, features a narrow diameter, allowing you to aim precisely around or through obstacles like fences, utility poles, or tree branches.

Versatile and Easy to Learn Software

The Leica Builder Electronic Total Station's powerful software solution, PowerSite, is designed to be easy to use yet serve as a complete solution for all of your measuring needs. PowerSite works together with the Construction Data Manager, a Windows-based application that handles firmware upload, data upload and download, and the installation of up to three out of 24 additional languages on the control panel. Setup with control line or coordinates, for example, follows the same procedure used when setting up with tape, and both also use the preset axis automatically  as the reference line, allowing you to work with line and offset values straight from your original plan. And of course, the easy choice of setup positions enables you to take measurements quickly and efficiently. You can also increase usability even further by adding a Leica handheld data collector. 

Five Pre-loaded Software Applications for Maximum Usability

Nine pre-loaded software applications come with your Leica Builder Total Station, allowing you to easily figure out the measurements for nine common measuring functions:

Layout Function: Check the alignment of columns, formworks, and fencing lines, and ensure against racking in greenhouses or other structures.

Area and Volume: Ideal for tender preparations of all kind. Check the fit for windows, the volume of asphalt needed for a parking lot, or simply capture aligned surfaces on the spot. Get fast volume determination of stockpile monitoring, cutting to formation, and mass haul cuts and fills, allowing you to keep tabs on your earthworks progress as the day progresses.

As-Built: Use the as-built function to ensure your blueprints are up to date and reflect the latest changes. With PowerSite, you can instantly transfer and update new data, or record measurements for drafting a completely new blueprint.

Hidden Point: Obtain measurements for points not directly visible with the hidden point function; PowerSite software reveals the position of the hidden point, total station, and reflector in just a few steps.

Angle and Distance: Check the height clearance under a bridge, mark ground floor elevations, and transfer reference heights in one work step.

Tie distance: Used to compute horizontal distance, height difference, and grade between two target points, tie distance is the perfect solution for figuring out whether or not there is a clearance under a roof for that crane, or checking the drainage of a grade.

Coordinate Geometry Calculations: A graphical display on the control panel shows the position of the station, used new points, directions, distances, and the new calculated point, allowing you to easily figure out this normally complicated measurement.

Layout Line/Arc/Spiral: Easily plot the lines for a road or spiral staircase; the PowerSite software allows you to stake out and check points relative to a road alignment.

Enhance Productivity 

The Leica 400 Total Station boasts several other features that help you improve your on-site productivity. Leica's endless drives make it easy to rotate the total station a full 360 degrees while staying steady at all times. Once you finish measuring your target, you can store up to 50,000 points in the Leica Builder's internal memory, or add a Leica USB to easily store or transfer data. Or, use the included cable to download data directly to our PC or laptop, or upload a new AutoCAD plan. Protect your Builder Total Station with the Theft Protection Feature, which uses a Personal Identification Number upon start-up. The system locks down after the wrong PIN number is typed in, and can only be re-opened with the Personal Unblocking Code located on the delivery papers for your Leica Total Station.

With the Leica Builder 400 (9-Second) Reflectorless Total Station, there are no boundaries: anyone can take precise measurements, anywhere, anytime. It's the ideal way to save time, money, and improve safety, leaving you free to focus on being a leader in your field.

Features for the Leica Builder 400 9 Second Reflectorless Total Station

  • 9-second accuracy
  • 50,000-point internal memory
  • 50 foot range
  • Laser plummet
  • Pinpoint laser technology
  • On-board field software
  • Setup wizard
  • Construction Data Manager for data management for PC or laptop; Windows interface
  • USB stick and RS232 serial port
  • Theft protection
  • 20-hour battery life
  • Water resistant and dustproof to IP-55
  • Single graphic LCD display
  • Alphanumeric keyboard
  • Multilingual support with 24 languages

Specifications for the Leica Builder 400 9 Second Reflectorless Total Station

Weight 11.2 lbs. (5.1 kg)
Dimensions 23 in. x 18 in. x 15 in. (58.42 cm x 45.72 cm x 38.1 cm)
Warranty 1-year manufacturer's warranty
Protection Class IP55 (protected against hazardous parts, dust protected, protected against water jets from any angle.)
Tripod Thread 5/8-11 in.
Internal Memory 50,000 internal points
Software PowerSite, Construction Data Manager
Tribrach fixed
Angle Measurement
Measuring Method/Reading System absolute, continuous
Accuracy 9-second
Distance Measurement
Unit of Measure (distance display) in,ft,mm,m
Tilt Sensor/Compensator
Range 4 arcmin
Setting Accuracy 2 arcsec
Power Source Li-Ion batteries
Battery Life about 20 hours
Battery Life Alert yes
Voltage 7.4 V
Optical Plummet
Image erect
Circular Bubble Vial 6 minutes/2 mm
Electronic Level 6 arcseconds
Image erect
Diameter of Objective Lens (Aperture) 1.57 in.(40 mm)
Magnification 30x
Field of View 2.6 m at 100 m
Sight Distance Precision/Focus Range 5.6 ft/1.7 m to infinity
Reflectorless yes
Display and Keypad
Type 6-line graphic LCD
Sides single-sided
Keys 20
Backlight yes
Pixels 280 x 160 pixels
Operating -4ºF to 122ºF (-20C to +50)
Storage -40ºF to 158ºF (-40ºC to +70ºC)
Surveying and Construction yes
Mapping and GIS (geographic information systems) yes
Utilities yes
Environment Studies yes
Geomarking yes
Archaeology yes
Accident Reconstruction yes
Measurement Range (under fair weather conditions)
Single Prism 2600 ft. (800 m)
Reflective Tape 560 ft. (170 m)
Cat Eye/Flat Prism 820 ft. (250 m)
Coordinate Measurement Point yes
Angle and Distance Stake Out yes
Stake Out Line yes
Offsets yes
Missing Line yes
Remote Elevation yes
Resection yes
Area Calculation yes
Measurement Time
Fine < 1 s
Rapid < 0.3 s
Tracking 1.0 s
Laser Plummet
Accuracy 0.0590 in. (1.5 mm) at 4.92 ft. (1.5 m) instrument height
Class Visible red laser class 2
Laser Pointer
Reflectorless range 50 ft (15 m)
Wavelength 650 nm - 690 nm
Range to reflective tape 50 ft (15 m)
Range to glass prism 1640 ft (500 m)
USB USB memory stick and USB device port
Pin Port RS232

Customer Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Use spaces to separate tags. Use single quotes (') for phrases.